A high-performance construction solution applicable to all types of buildings. Approved internationally, we propose the best solution for your project.
The PHI is a system of vertical profiling very simple, economical and easy to install.
It is designed meticulously to meet each and every one of the necessary mechanical and anticorrosive demands in the building.
Being a system of profiling, it can be installed on solid, perforated or hollow support. The PHI system offers the possibility of regulation in the vertical and horizontal axes. Complying with UNE 41957 regulations.
The system allows an immediate load and its assembly is independent of atmospheric conditions. In addition, due to the reduction in the number of fixings on the support, a more continuous thermal insulation is achieved, breaking a large number of thermal bridges.
The PSI is a system of vertical profiling very simple, economical and easy to install.
Its benefits are lower than that of PHI, that is why it is destined to smaller size.
The Epsilon system offers the possibility of regulation in the vertical and horizontal axes, fulfilling in the same way as the previous one with the UNE 41957 standard.
The system is manufactured with the same materials as PHI, so it is a system with all the guarantees, excellent raw materials and more economical where, due to the required mechanical performance, it is not necessary to support a high load resistance
It is a subsystem capable of working in conjunction with the PHI, PSI or other special systems.
The horizontal profile (Link) made of aluminum alloy EN AW 6063 T5, is a very light and resistant profile thanks to its tubular section. It has a fluted flat fin to anchor it to the vertical profiling, by means of a self-drilling screw and a safety washer, it has a channel specially designed to house the “Link” staples by means of a clipping system, which provides great agility at the time of place the system.
The horizontal profile is ideal for the placement of any cutting of stone, both for continuous joint and to kill. The system with horizontal profiling can be used with either nail clamps, concealed nail, or pivot (21 or 32 mm outlet).
It is a fixing system for stone cladding. The FIX system is based on individual and point anchors that are placed as a safety element for mortars.
The FIX system for new construction consists of 7 types of staples, with different geometries and properties. They are manufactured in stainless steel A-2 (AISI-304) that offer appropriate values of mechanical resistance and atmospheric corrosion.
These staples, without welding, on the one hand are fixed to a particular support or to the building itself and on the other side to the stone plate.
It is also offered for repairs of plating, two safety staples, FIX ECO and FIX ECO NAIL, with which fixed coatings are fixed where there is a risk of detachment.
The Aplomado system DSETA 2 is a vertical profiling system, it constitutes a metallic substructure destined to receive the solidary union of the clamps that hook the claddings.
The fixing of the profiling is made to the floor slabs to which it transmits the efforts it receives from the slab by means of floor anchors. The floor anchors offer a large load capacity and a wide range of regulation.
DSETA 2 is the fixing system for stone cladding. It consists mainly of 5 types of non-registrable staples that require a vertical profiling system such as the Aplomado System. The different staples are fastened to the vertical profile by means of a stainless steel shoulder.
The main characteristic of these systems is their capacity of horizontal displacement on the profile, which facilitates the attachment of claddings that are displaced with respect to the profile.
The Direct system is based on point and individual anchors so that vertical profiles are not needed for plumb.
This system is relatively inexpensive and often used in the coating of concrete walls, whether prefabricated or on site. It can be used on walls or walls of solid or semi-solid brick. It is not recommended in hollow block where the partition is less than 40 mm thick. Standard UNE 41957.
The system is entirely made of stainless steel A-2 (AISI-304) that offers appropriate values of mechanical resistance and atmospheric corrosion. It is constituted by a threaded shaft where on one side it is fixed to a certain support or to the building itself and on the other side, it is provided with a device which supports and retains the plate.
This device or nail can be hidden, with pivot and sight, for which there is the Direct strow with retaining spring for anchoring with irregular thicknesses and the Direct basic, a new system for clamping with fixed thicknesses designed to be extremely economical without losing a quality apex.
The Standard system is based on point and individual anchors with vertical and in-depth regulation. It is a body without solder that on the one hand is fixed to a certain support and on the other includes a clamp for the coating.
Three different models are made, the first normal, the second (Brake) with a safety washer that acts as a brake on the possible slip of the anchor and the fixation, and a third, which also includes the brake but is also built with greater thickness and a rear nut giving it much more resistance.
This system is often used in the covering of concrete walls, whether they are prefabricated elements or construction elements. It can also be used on walls or walls of solid or semi-solid brick. They are not recommended in brick or hollow block where the partition is less than 40 mm thick.
Plans of assembly of profiling. Technical constructive details by the best professionals.
Perfectly finished finishes in marble, granite, slate, any other natural stone.
Maintenance and periodic reviews of the installation in compliance with the regulations.
Different custom anchoring systems for installation.
We have more than 20 years of experience and the best professionals.
Collaborations with different partners and partners for a complete and careful installation.